Customize Consent Preferences

We use cookies to help you navigate efficiently and perform certain functions. You will find detailed information about all cookies under each consent category below.

The cookies that are categorized as "Necessary" are stored on your browser as they are essential for enabling the basic functionalities of the site. ... 

Always Active

Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.

No cookies to display.

Functional cookies help perform certain functionalities like sharing the content of the website on social media platforms, collecting feedback, and other third-party features.

No cookies to display.

Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics such as the number of visitors, bounce rate, traffic source, etc.

No cookies to display.

Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors.

No cookies to display.

Advertisement cookies are used to provide visitors with customized advertisements based on the pages you visited previously and to analyze the effectiveness of the ad campaigns.

No cookies to display.

PCB'yi mekanik yapıya nasıl sabitleyebilirim?

Dört adet lens düzeneğine mekanik olarak bağlanan görüntüleme sensörlü bir PCB tasarladım. 2-56 vidalar. I'm noticing that even though the screws are holding the board tightly against the mechanical structure if I flick or lightly knock the the assembly the image "hamle". I'm hoping to get a few suggestions for ways to fix the PCB to the mechanical structure. Yapıştırıcılar veya benzerleri için herhangi bir öneri? Başka bir şey?

You probably want to add some mechanical stiffeners to your board. It may be too late for that, ancak, since that is usually factored into the PCB design (unless you want to design a new PCB and mounting fixture).

The stiffener would be a rigid piece of metal or other material that runs along the length of your PCB (or sometimes across the center of it) with fasteners to hold the board tightly against it. It can also provide the mounting interface to your optics and/or thermal relief (soğutucu).

#PCB Düzeneği #PCB Tasarımı

https://www.youtu.be/5tW8QssLHzM?si=LB3VyjmiX4U0L-OX

Resmi Oliver Smith

Oliver Smith

Oliver, PCB tasarımı konusunda yetenekli deneyimli bir elektronik mühendisidir, analog devreler, gömülü sistemler, ve prototipleme. Derin bilgisi şematik yakalamaya kadar uzanıyor, cihaz yazılımı kodlaması, simülasyon, Yerleşim, test yapmak, ve sorun giderme. Oliver, elektrik tasarımı yeteneklerini ve mekanik yeteneğini kullanarak projeleri konsept aşamasından seri üretime geçirme konusunda uzmandır.
Resmi Oliver Smith

Oliver Smith

Oliver, PCB tasarımı konusunda yetenekli deneyimli bir elektronik mühendisidir, analog devreler, gömülü sistemler, ve prototipleme. Derin bilgisi şematik yakalamaya kadar uzanıyor, cihaz yazılımı kodlaması, simülasyon, Yerleşim, test yapmak, ve sorun giderme. Oliver, elektrik tasarımı yeteneklerini ve mekanik yeteneğini kullanarak projeleri konsept aşamasından seri üretime geçirme konusunda uzmandır.

Başkaları Ne Soruyor?

Do you use SMT or THT for USB mini B connector?

This question is about the advisability of continuing to use a USB mini-B right angle surface mount connector in my pcb designs. On occasion we see one of these connectors peel back or delaminate off the pcb. Immediately the question is asked, why didn’t you use a through hole connector?

Blog Makalelerinden Ayrıntılı Tavsiyeleri Okuyun