We value your privacy

We use cookies to enhance your browsing experience, serve personalized ads or content, and analyze our traffic. By clicking "Accept All", you consent to our use of cookies. Read more in the Privacy Policy

Customize Consent Preferences

We use cookies to help you navigate efficiently and perform certain functions. You will find detailed information about all cookies under each consent category below.

The cookies that are categorized as "Necessary" are stored on your browser as they are essential for enabling the basic functionalities of the site. ... 

Always Active

Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.

No cookies to display.

Functional cookies help perform certain functionalities like sharing the content of the website on social media platforms, collecting feedback, and other third-party features.

No cookies to display.

Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics such as the number of visitors, bounce rate, traffic source, etc.

No cookies to display.

Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors.

No cookies to display.

Advertisement cookies are used to provide visitors with customized advertisements based on the pages you visited previously and to analyze the effectiveness of the ad campaigns.

No cookies to display.

How can I electrically isolate a PCB from a heat sink?

I have a set of LED driving lights for motorcycle that must be wired through a ground-leg pulse width modulation dimmer. The problem is the mounting bracket for the lights is grounded, so the lamp shorts to ground through the motorcycle chassis and the PWM dimmer cant dim the lamps. How do I handle this problem?
  • Use Kapton tape
  • Use Sil-pad and shoulder washer. If you use a sil-pad the screw will still electrically connect the componet tab with the heat sink, soashoulder washer should be used to isolate the screw and the tab.

Lees verder: LED PCB-assemblage

#PCB Assembly #PCB Design

Picture of Olivier Smit

Olivier Smit

Oliver is een ervaren elektronica-ingenieur met kennis van PCB-ontwerp, analoge circuits, ingebedde systemen, en prototyping. Zijn diepgaande kennis omvat schematisch vastleggen, firmware-codering, simulatie, indeling, testen, en probleemoplossing. Oliver blinkt uit in het omzetten van projecten van concept naar massaproductie met behulp van zijn elektrische ontwerptalenten en mechanische vaardigheden.
Picture of Olivier Smit

Olivier Smit

Oliver is een ervaren elektronica-ingenieur met kennis van PCB-ontwerp, analoge circuits, ingebedde systemen, en prototyping. Zijn diepgaande kennis omvat schematisch vastleggen, firmware-codering, simulatie, indeling, testen, en probleemoplossing. Oliver blinkt uit in het omzetten van projecten van concept naar massaproductie met behulp van zijn elektrische ontwerptalenten en mechanische vaardigheden.

Wat anderen vragen

How do I use two antennas with a single Bluetooth module? (BLE repeater)

I am working on a project that uses small Bluetooth low energy (BLE) beacons to track important items. Is there a way to connect two antennas to a single BLE module that could either listen/broadcast on both antennas or multiplex between the two? Or any other idea?

Olivier Smit december 7, 2023

How to handle feedline of bluetooth PCB connected to a 2.4GHz chip antenna?

I’m making a 4 layer PCB prototype that uses a bluetooth mcu connected to a 2.4GHz chip antenna. I’m thinking about what to do with the feedline, whether it should be buried on one of the middle layers, or left on the top layer. To get a 50 ohm line, should I choose top layer with 13-mil width or buried miccrostrip with 7-mild width?

Olivier Smit November 30, 2023
Blader door alle vragen

Lees gedetailleerd advies uit blogartikelen

Lees alle artikelen

markten

PCB

Middelen

Neem contact op

Copyright ©2025 MOKO Technology | Uw vertrouwde EMS-partner Guangdong ICP Nr. 15085690

Facebook Twitter Linkedin Youtube