BGA Reballing: An Essential Process in Electronics Repair and Maintenance

BGA reballing emerges as a critical repair technique for modern electronic devices. Aujourd'hui, electronic devices are becoming increasingly complex and versatile to meet evolving user demands. These devices often rely on Réseau de grille à billes (BGA) paquets for efficient functionality. pourtant, over time, BGAs may develop issues that require precise rework solutions. This is where BGA reballing comes into play. Dans ce blog, we’ll explore what BGA reballing is, why it is essential, the tools required, and the step-by-step process involved.

What Is BGA Reballing?

BGA reballing is a process to replace the solder balls on a Ball Grid Array package. Premier, let’s figure out what BGA is. It is a surface-mount packaging that is featured with an array of tiny solder balls on the underside, commonly used for integrated circuits to provide electrical and mechanical connections to the PCB. pourtant, its solder balls may counter degrade, crack or become contaminated over time, which would cause connectivity issues and affect devices’ performance. And reballing is a useful method to fix it by replacing the damaged solders balls with new ones.

Why Is BGA Reballing Needed?

BGA reballing becomes essential for several reasons:

  • Repair of Damaged Solder Balls

Solder ball conductivity can be broken or severed by stress, thermal cycling and aging. En tant que tel, we can rely on BGA reballing method to restore functionality of components rather than replacement.

  • Reuse of Expensive Components

When we deal with some faulty circuit boards, we can reuse these high-value components like processors or GPU by reballing to decrease costs.

  • Correction of Manufacturing Defects

Pendant la fabrication, if there are misaligned or improperly formed solder balls, the BGAs would get defected. And BGA reballing can correct these issues, which is one of the major uses of BGA reballing process.

  • Refurbishment of Electronics

BGA reballing is a major process in the refurbishment (retravailler) industrie, which is used to restore functionality for used or defective electronic components.

Tools Required during the BGA Reballing

To carry out the raballing process well, we need to use the right tools. Let us look at some of the tools that are needed for reballing:

  • Fer à souder

A soldering iron is a hand held device that delivers heat to the solder material which melts the solder to form strong connections between components and the BGA PCB assembly. Its top is the soldering iron tip to heat the solder precisely, and its handle is insulated to ensure safe handling.

  • Desoldering Wire

Desoldering wire, also known as solder wick, is a tool used to remove unwanted solder. Heat the wire, and when the molten solder is absorbed in the wire, it is easier to clean off the area. It is usually made of a fine copper braid coated with rosin flux, d'habitude 18 à 42 AWG in thickness.

  • BGA Reballing Station

It is a specialized workstation designed for performing BGA reballing tasks. This station includes holders that are used to secure BGA components, heating tools to soften the solder, et SMT stencils to ensure uniform solder balls.

  • Solder Balls

Solder balls are small spherical pieces of solder placed on the underside of a BGA (Réseau de grille à billes) emballer. During the assembly process, the solder balls melt and solidify, forming reliable joints between the BGA and the PCB.

BGA Reballing Process: 7 Key Steps Involved

BGA reballing is a skill and accuracy required, complex multi stage operation. Here is an overview of the steps involved:

Étape 1: Préparation

Technicians look at the BGA chip for visible damage before starting. Then clean the original surface and ensure the component is ready for reballing.

Étape 2: Solder Balls Removal

We have to remove the original solder balls in this stage. This can be achieved using both a hot air rework station or an IR reflow oven.

Étape 3: Cleaning the BGA Package

ensuite, remove residual solder and contaminants from the underside of the BGA package. This can be done by flux, solder wick or a desoldering tool. Finally we have a clean, flat surface for the new solder balls.

Étape 4: Reballing

Put stencils over the BGA components, then place the preformed solder balls accurately or applying soldering paste so as to create new solder balls.

Étape 5: Reflowing the Solder Balls

BGA package is heated using a rework station or reflow oven to melt the solder balls, so they can be mounted onto the component firmly. As far as temperature goes, it should run in this range from 220°C to 250°C to avoid overheating.

Étape 6: Inspection

When the re-balled BGA components are cooling down,technicians use a microscope to check if there is any issue, ensuring that all solder balls are formed and aligned properly.

Étape 7: Reinstallation

The re-balled BGA is mounted back onto the PCB via a rework station. The connections are checked and verified for correct working.

Choosing MOKO Technology for BGA Reballing Service

MOKO Technology is the company that provides BGA reballing services and has rich experienced in PCB assembly and repair. We are capable of salvaging high value components, remedying manufacturing defects, and meeting specified soldering requirements, and we do all this with fast turnaround, competitive pricing and superb service backed by a wide array of equipment, trained and qualified technicians. If you’d like to talk to us about your BGA reballing inquiries, reach out to us today.

Will Li

Will maîtrise les composants électroniques, Processus de production de PCB et technologie d'assemblage, et possède une vaste expérience dans la supervision de la production et le contrôle de la qualité. Sur le principe d'assurer la qualité, Will fournit aux clients les solutions de production les plus efficaces.

Messages récents

What Are PCB Stiffeners? Exploring Their Types, Uses, and Thicknesses

Do you know what PCB stiffeners are? They are widely used in flex and rigid-flex

2 weeks ago

Why PCB Warpage Happens and How You Can Prevent It?

Dans le processus de fabrication des PCB, PCB warpage is a common problem that manufacturers would encounter.

1 month ago

What Is a PCB Netlist? Tout ce que vous devez savoir est ici

In the world of printed circuit board design and manufacturing, precision and accuracy are paramount.

2 months ago

What Is Solder Wetting and How to Prevent Poor Wetting?

Soldering is a cornerstone technique in electronics assembly, it's used to connect electrical pieces and

2 months ago

7 Critical Techniques to Improve PCB Thermal Management

Aujourd'hui, electronic products are both compact and lightweight while performing a variety of functions. Ce…

2 months ago

What Is BGA on a PCB? A Complete Guide to Ball Grid Array Technology

As technology continues to advance in the electronics industry, packaging remains one of the key

3 months ago